Spare Assets For Sale
MD&A has Spare Assets for Sale:
Major Components from a New 7FA.03 Gas Turbine & 7FH2 Generator – Manufacture Date: 2003
MD&A has the following major components from a new 7FA.03 gas turbine & 7FH2 Generator. These never-used, zero-hour components have been stored in an indoor, climate-controlled environment, providing perfect working order and increased efficiency at a reduced cost. Available components:
- 7FA.03 Rotor, Flared Compressor, Unbucketed
- 7FH2 Generator Stator
- Compressor Discharge Casing
- Turbine Casing
- Diffuser
- Inner Barrel
- Fixators
- Control Valves – Extraction (1022)
- Load Coupling Hardware – Riverhawk (1309)
- Inlet Plenum Assy (1612)
- Valves (A037)
- Exhaust (A042)
- Battery Chargers/Rectifiers
- Bentley Nevada 3500 Vibe Monitor
- Motor Controllers / Relays
- DC Lube Oil Pump & Motor and Duplex strainer
- Weatherhood Assy
- Cab Off Section/Turning Gear Gas dryer (G2M0)
- Fuel Gas Heater (G010)
- Air Processing Unit (A130)
- Heat Exchangers
Contact MD&A Parts for additional information – 518-885-3199
Components for Sale for a New Frame 7EA Gas Turbine-Generator – Manufacture Date: 2009
MD&A has the following components for sale for a 7EA gas turbine. This zero-hour 2009 turbine has been stored in an indoor, climate-controlled for proven power and unprecedented performance. Available components:
- 7A6 Stator
- Switch Gear
- GNAC & Non-Segregated Bus Duct
- Generator Protection Panel
- Exhaust Plenum, Expansion Joint, Flex Seals, Wing & Cowl
- Fixators
- Battery Chargers (2)
- LO – Heat Exchangers/Coolers (2)
- Hydraulic Pump, Motor, Accumulator
- Water Injection (A035)
- Temp Regulator Valve
- Liquid Fuel HP Filter (E040)
- Atomizing Air Compressor (Primary)
- Atomizing Air Compressor & Motor (Aux)
- Air Processing Unit (A130)
- 4″ Check Valves (Qty 5)
- Flow Regulator
- Pressure Regulator
- IGV Actuator
- Riverhawk Coupling Hardware
Contact MD&A Parts for additional information – 518-885-3199
Generator Fields:
NEW 7FH2 Generator Field—Available Now!
- New Field with zero hours has been completely wound with new coils and possesses the latest in rewind technologies
- The field was assembled with MD&A’s patented “top hat” modifications to eliminate slot spring migration
- Field forging will have undergone NDE and inspections to ensure its long term viability
- The field will have been high-speed balanced with a full heat run to ensure no shorted turns
- The field is available to support forced or emergent outage needs
Contact Tom Brittain at MD&A for additional information – (314) 880-3000 or (518) 860-9127
NEW 7A6 Generator Field— (2) Available Now!
- New Field with zero hours will be completely wound with new coils and possesses the latest in rewind technology
- Field forging has undergone NDE and inspections to ensure long term viability
- High speed balanced with a full heat run to ensure no shorted turns
- The fields are available to support forced or emergent outage needs
Contact Tom Brittain at MD&A for additional information – (314) 880-3000 or (518) 860-9127
Refurbished 7FH2 Generator Rotor—Available Now!
- Completely rewound with existing copper and possesses the latest in rewind technology
- Reassembled with MD&A’s patented “top hat” modifications to eliminate slot spring migration
- Field forging has undergone NDE and inspections to ensure long term viability
- High speed balanced with a full heat run to ensure no shorted turns
- Available to support forced or emergent outage needs
Refurbished 7FH2 International Generator Rotor—Available Now!
- Completely rewound with existing copper and possesses the latest in rewind technology
- Reassembled with MD&A’s patented “top hat” modifications to eliminate slot spring migration
- Field forging has undergone NDE and inspections to ensure long term viability
- High speed balanced with a full heat run to ensure no shorted turns
- Available now to support forced or emergent outage needs
- Currently Stored in St. Louis ready to transport and support any forced outage needs
Contact Tom Brittain at MD&A for additional information – (314) 880-3000
7FH2 Stator Rewind Kit—Available Now!
- 7FH2 Stator Rewind Kit with 6” of Step Iron Stator Bars
7A6 Stator Rewind Kit—Available Now!
Contact Tom Brittain at MD&A for additional information – (314) 880-3000
Newly Added Stock Inventory – Available Now!
Newly added to our stock and in-shop equipment to lessen the outage season downtime with our brand new Toshiba 200 CNC lathe.
Machined in the MD&A STL service shop
Each size will have a set of two (2) Retaining Ring forgings
These will fit units ranging from GE frame 5 up to the large GE® LST’s (G2/G3) units and all other OEMs in the size frames listed below
Available in 5-6 days after receipt of final drawings
- Forging Set (2 Rings) #1
OD 42.00″
ID 31.00″
L 31.00″ - Forging Set (2 Rings) #2
OD 47.00″
ID 36.00″
L 36.00″ - Forging Set (2 Rings) #3
OD 42.00″
ID 34.00″
L 24.00″ - Forging Set (2 Rings) #4
OD 34.00″
ID 26.00″
L 20.00″
Contact Tom Brittain at MD&A for additional information – (314) 880-3000
![]() |
![]() |